Netopia Firmware 4000-Series Manual de usuario Pagina 282
- Pagina / 314
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
11-8 Firmware User Guide
■ Select GET ROUTER FIRMWARE FROM SERVER and press Return. You will see the following dialog box:
■ Select CANCEL to exit without downloading the file, or select CONTINUE to download the file. The system
will reset at the end of the file transfer to put the new firmware into effect. While the system resets, the
LEDs will blink on and off.
Caution!
■ Be sure the firmware update you load onto your router is the correct version for your particular model.
Some models do not support all firmware versions. Loading an incorrect firmware version can permanently
damage the unit.
■ Do not manually power down or reset the Router while it is automatically resetting or it could be damaged.
■ If you choose to download the firmware, the TFTP Transfer State item will change from Idle to Reading
Firmware. The TFTP Current Transfer Bytes item will reflect the number of bytes transferred.
Downloading configuration files
The Router can be configured by downloading a configuration file using TFTP. Once downloaded, the file
reconfigures all of the router’s parameters as if someone had manually done so through the console port.
To download a configuration file, follow these steps:
■ Select TFTP Server Name and enter the server name or IP address of the TFTP server you will use. The
server name or IP address is available from the site where the server is located.
■ Select Config File Name and enter the name of the file you will download. The name of the file is available
from the site where the server is located. You may need to enter a file path along with the file name (for
example, bigroot/config/myfile).
■ Select GET CONFIG FROM SERVER and press Return. You will see the following dialog box:
■ Select CANCEL to exit without downloading the file, or select CONTINUE to download the file. The system
will reset at the end of the file transfer to put the new configuration into effect.
+--------------------------------------------------------------------+
+--------------------------------------------------------------------+
| Are you sure you want to send a firmware file to your Netopia? |
| The device will restart when the transfer is complete. |
| |
| CANCEL CONTINUE |
| |
| |
+--------------------------------------------------------------------+
+----------------------------------------------------------------------+
+----------------------------------------------------------------------+
| Are you sure you want to send a saved configuration to your Netopia? |
| |
| |
| CANCEL CONTINUE |
| |
+----------------------------------------------------------------------+
- Copyright 2
- Part Number 2
- Console-based Management 12
- Netopia Console Menus 12
- Netopia Models 13
- Configuring Telnet software 14
- Example back panel 15
- 1-8 Firmware User Guide 18
- WAN Configuration 19
- ADSL Line Configuration screen 20
- SDSL/IDSL Configuration screen 21
- IDSL Line Configuration screen 23
- T1 Line Configuration screen 25
- Frame Relay Configuration 27
- Frame Relay DLCI configuration 29
- Multiple ATM PVC overview 34
- Multiple ATM PVC configuration 34
- Editing circuits 38
- Changing a circuit 39
- The Default Profile 46
- Scheduled Connections 47
- Viewing scheduled connections 48
- Adding a scheduled connection 49
- Set Weekly Schedule 50
- Set Once-Only Schedule 51
- System Configuration Screens 53
- Filter Sets 54
- Stateful Inspection firewall 55
- Stateful Inspection Options 56
- Exposed Addresses 58
- Date and time 60
- Console Configuration 61
- Security 61
- Upgrade Feature Set 61
- RFC-1483 Transparent Bridging 62
- 2-48 Firmware User Guide 66
- Features 68
- Dynamic mapping 69
- WAN Network 70
- LAN Network 70
- Supported traffic 71
- MultiNAT Configuration 72
- IP setup 73
- NAT rules 75
- Add Map 76
- Modifying map lists 79
- Adding Server Lists 81
- Modifying server lists 84
- Deleting a server 86
- IP profile parameters 87
- IP Parameters 89
- NAT Associations 91
- 3-26 Firmware User Guide 92
- IP Passthrough 93
- 3-28 Firmware User Guide 94
- First Come First Serve Mode 95
- A restriction 96
- MultiNAT Configuration Example 97
- Notes on the example 100
- 3-36 Firmware User Guide 102
- Overview 103
- Transit Internetwork 104
- About PPTP Tunnels 106
- About IPsec Tunnels 109
- About ATMP Tunnels 110
- Encryption Support 112
- ATMP/PPTP Default Profile 113
- VPN QuickView 115
- Dial-Up Networking for VPN 116
- Installing the VPN Client 119
- Windows 98 VPN installation 120
- PPTP example 122
- ATMP example 124
- Windows Networking Broadcasts 127
- 4-26 Firmware User Guide 128
- 4-28 Firmware User Guide 130
- Adding an IKE Phase 1 Profile 134
- Key Management 139
- Enhanced Dead Peer Detection 142
- Multiple Network IPsec 144
- IPsec Manual Key Entry 149
- VPN Quickview 150
- IP Setup 154
- IP subnets 156
- Static routes 158
- Viewing static routes 159
- Adding a static route 160
- Modifying a static route 161
- Deleting a static route 161
- RIP-2 MD5 Authentication 162
- IP Setup 6-11 163
- The IP Setup screen appears 163
- 6-12 Firmware User Guide 164
- Adding a key 166
- Changing or deleting a key 167
- IP Address Serving 169
- IP Address Pools 172
- DHCP NetBIOS Options 174
- More Address Serving Options 176
- IP Setup 6-29 181
- DHCP Relay Agent 182
- Connection Profiles 184
- Multicast Forwarding 186
- External Dial Backup Support 190
- Backup Configuration screen 193
- Management/Statistics 198
- QuickView 200
- Event Logs 200
- SNMP Support 201
- Backup Default Gateway 201
- IP Setup screen 203
- Backup Management/Statistics 204
- 7-18 Firmware User Guide 206
- Introduction 207
- Configuring the Voice Features 208
- Quick View Status Overview 211
- General status 212
- Current status 213
- Status lights 213
- Statistics & Logs 214
- Event Histories 214
- WAN Event History 215
- Device Event History 215
- IP Routing Table 217
- General Statistics 217
- Physical Interface 218
- Network Interface 218
- System Information 219
- ATM MIB (RFC2515) 220
- ADSL: ADSL MIB (RFC2662) 220
- The SNMP Setup screen 221
- SNMP traps 222
- Setting the IP trap receivers 223
- Viewing IP trap receivers 223
- Modifying IP trap receivers 223
- Deleting IP trap receivers 223
- 9-14 Firmware User Guide 224
- Suggested Security Measures 225
- UPnP Support 226
- Superuser configuration 227
- Limited user configuration 228
- Advanced Security Options 229
- User access password 231
- User menu differences 232
- WAN Configuration screens 233
- System Configuration menu 235
- IP Setup menu 235
- X-Modem File Transfer menu 236
- Statistics & Logs menu 236
- Security 10-13 237
- Quick Menus 238
- User Accounts 239
- Telnet Access 241
- About Filters and Filter Sets 242
- Filter priority 243
- How individual filters work 244
- Parts of a filter 245
- Port numbers 245
- Port number comparisons 246
- Other filter attributes 246
- Putting the parts together 247
- Filtering example #1 248
- Filtering example #2 248
- Design guidelines 249
- An approach to using filters 250
- Adding a filter set 251
- Adding filters to a filter set 252
- Viewing filters 254
- Modifying filters 254
- Deleting a filter set 255
- A sample filter set 255
- Possible modifications 257
- TOS field matching 259
- Firewall Tutorial 261
- Firewall design rules 262
- Binary representation 263
- Logical AND function 263
- Implied rules 263
- Filter basics 264
- Example network 265
- Example 1 265
- Example 2 266
- Example 3 266
- Example 4 267
- Example 5 267
- Configuration Management 268
- 10-46 Firmware User Guide 270
- TFTP and X-Modem 271
- Call Filtering 272
- 10-50 Firmware User Guide 274
- Trace Route 278
- Telnet Client 279
- Factory Defaults 280
- Updating firmware 281
- Downloading configuration files 282
- Uploading configuration files 283
- Restarting the System 286
- Configuration Problems 289
- Console connection problems 290
- Network problems 290
- Power Outages 291
- Technical Support 292
- What is IP? 293
- About IP Addressing 293
- Subnets and subnet masks 294
- Subnet masks 295
- Network configuration 296
- Distributing IP Addresses 297
- Configuration 299
- Using address serving 300
- A DHCP example 302
- Nested IP Subnets 303
- Internet 304
- Broadcasts 306
- Binary Conversion Table C-1 307
- C-2 Firmware User Guide 308
Relacionado con productos y manuales para Hardware Netopia Firmware 4000-Series
Hardware Netopia Network Card Manual de usuario
(2 paginas)
(2 paginas)
Hardware Netopia D3232 IDSL Manual de usuario
(138 paginas)
(138 paginas)
Hardware Netopia 4652 Manual de usuario
(45 paginas)
(45 paginas)
Hardware Netopia 2240N-VGX Manual de usuario
(3 paginas)
(3 paginas)
Hardware Netopia R2020 Manual de usuario
(312 paginas)
(312 paginas)
Hardware Netopia 4622 T1 Manual de usuario
(44 paginas)
(44 paginas)
Hardware Netopia 2200 Manual de usuario
(351 paginas)
(351 paginas)
Hardware Netopia 2241N-VGX Manual de usuario
(2 paginas)
(2 paginas)
Hardware Netopia 3347W Manual de usuario
(44 paginas)
(44 paginas)
Hardware Netopia R5300 Manual de usuario
(290 paginas)
(290 paginas)
Hardware Netopia Network Adapte Manual de usuario
(19 paginas)
(19 paginas)
Hardware Netopia 4541 Manual de usuario
(209 paginas)
(209 paginas)
Hardware Netopia Routers R-Series Manual de usuario
(11 paginas)
(11 paginas)
Hardware Netopia 4600 Manual de usuario
(2 paginas)
(2 paginas)
Hardware Netopia Router PN Series Manual de usuario
(301 paginas)
(301 paginas)
Hardware Netopia 4752 Manual de usuario
(284 paginas)
(284 paginas)
Hardware Netopia 3300 Manual de usuario
(334 paginas)
(334 paginas)
Hardware Netopia 4686-XL Manual de usuario
(2 paginas)
(2 paginas)
Hardware Netopia 3356(EU Manual de usuario
(2 paginas)
(2 paginas)
Samsung WW10H8430EW/SA manuály
Uživatelské manuály a uživatelské příručky pro Pračky Samsung WW10H8430EW/SA.
Poskytujeme 1 manuály pdf Samsung WW10H8430EW/SA ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentarios a estos manuales